DE NEEF® HA CUT CFL AF

Product Description

In its uncured form, HA Cut CFL AF is a dark brown, non-flammable liquid without phthalate plasticizers. HA Cut CFL AF is a next generation 1-component injection resin with improved waterproofing and water cutting performance. When it comes in contact with water, the grout expands and quickly (depending on temperature and the amount of catalyst HA Cut Cat AF used) cures to a tough, rigid, closed-cell polyurethane foam that is generally unaffected by corrosive environments.

Product Advantages

• ADR free transport
• Next generation resin with improved waterproofing performance.
• Improved cell structure of the cured compound resulting in better mechanical properties and durability.
• Non-phthalate  resins, REACH compliant.
• Improved performance at temperatures below 5°C, no crystallization of HA Cut Cat AF.
• Fast, Extra-Fast and Super Extra-Fast catalysts available for applications where the standard catalyst reaction speed is insufficient due to low temperatures or very high-water flow. (See respective Technical Data Sheet).
• HA Cut CFL AF forms a rigid gasket with high strength in the joint or crack.
• Non-flammable, non-solvent formulation.
• User friendly: 1-component material.
• Controllable reaction times: by using catalyst curing times can be reduced.
• Cured compound is resistant to most organic solvents, mild acids, alkalis and micro-organisms (*).
• KTW Potable Water approved.

^{(*) For chemical resistances please contact your local GCP representative.}

Field of Application

• Designed for cutting off gushing water leaks with a high flow rate and/or high pressure.
• Used to block water leaks in diaphragm walls.
• Filling large voids such as rock fissures, crushed faults, gravel layers, joints, cracks and honeycombs in concrete structures that are not subject to settlement or movement.
• Pre-injections for waterproofing and consolidation in front of the TBM, with drill-and-blast and NATM under wet condition.
• For curtain injection into gravel for containing chemicals under wet or dry conditions.
• For screen injection behind porous structures when high velocity water streams are present.

Application

Before commencing the injection, consult the Technical Data Sheets and Safety Data Sheet (SDS) to be familiar with the materials at hand. Always shake HA Cut Cat AF well before use.

1. Surface Preparation

• Remove surface contaminants and debris to establish the pattern of the crack or joint. Active leaking cracks larger than 3 mm need to be sealed with an approved method.
• Drill holes of the correct diameter for the selected packer. Drill at an angle of 45°. Preferably the holes should be drilled staggered around the crack to insure good coverage of the crack in case it is not perpendicular to the concrete surface.
• The depth of the bore should be approximately half of the thickness of the concrete. As a rule of thumb the distance of the drill point from the crack is half the wall thickness.
• Distance between holes can vary by 15 to 90 cm, depending on the actual situation.
• Insert the correctly sized packer into the hole up to 2/3 of its length. Tighten with a wrench or spanner by turning clockwise until enough tension has been reached to keep the packer in place during injection.
• Flush the crack with water before injecting with resin. This will flush out dust, debris and prime the crack for the injection resin and improve penetration of the product into the crack. Water in the crack will activate the resin.

2. Resin and Equipment Preparation

• Prepare the resin with the predetermined amount of catalyst. Shake HA Cut Cat AF well before use.
• No reaction with the resin will occur until the resin comes into contact with water.
• Protect the resin from water, since this will trigger a reaction in the container used and might cause the resin to harden or foam prematurely within the injection equipment.
• It is highly recommended to use separate pumps for the water and the resin injection to prevent cross contamination and blockages.
• The pumps should be thoroughly primed with DE NEEF® Washing Agent Eco to lubricate and dry the system before injection. We recommend the use of pneumatic or electric 1-component pumps. During the injection water will first flow from the crack, followed by foaming resin. After this, pure resin will flow from the crack.
• Stop pumping when the pure resin reaches the next packer.
• Move to the next packer and repeat the procedure. 
• After injecting through a few of the packers, go back to the first one and re-inject with resin.
• After the resin injection, water can be re-injected into the ports to cure resin left behind.
• Let the resin cure thoroughly before removing packers. The resulting holes can be filled with hydraulic cement.
• When the injection is finished, clean all tools and equipment which have been in contact with the resin with DE NEEF® Washing Agent Eco. This should be done within 30 minutes. Do not use solvents or other cleaning products since they give fewer positive results and can create hazardous situations.
• Products should be disposed according to local legislation.

3. Reactivity

With 10% HA Cut Cat F AF

With 10% HA Cut Cat XF AF

With 10% HA Cut Cat SXF AF

Appearance

HA Cut CFL AF: Dark brown clear liquid.
HA Cut Cat /F/XF/XF AF: Red transparent liquid.

Consumption

Must be estimated by the engineer or operator and depends on width and depth of the cracks and voids, which need to be injected and on the expansion rate of the chosen resin.

Packaging

HA Cut CFL AF

5kg, 25kg or 200kg metal drums

HA Cut Cat AF

0.5 or 2.5L plastic bottle or 20kg metal drum

HA Cut Cat F/XF/SXF AF

2.5L plastic bottle

Storage

HA Cut CFL AF is sensitive to moisture and should be stored in original container in a dry area. Storage temperature must be between 5°C and 30°C. Once the packaging has been opened, the useful life of the material is greatly  reduced and should be used as soon as possible.
Shelf life: 2 years.

Accessories

To be ordered separately

• Pumps
• Packers and connectors
• DE NEEF® Washing Agent Eco

(See respective Technical Data Sheets)

Health and Safety

Users must read and understand the product label and safety data sheet (SDS) for each system component before use. All users should acquaint themselves with this information prior to working with the material. Carefully read detailed precaution statements on the product label and SDSs before use. The most current SDSs can be obtained from the GCP website at gcpat.com or by  contacting GCP at +1-703-741-5970.

Technical Data / Properties